No.

Item #

AQUABOT ULTRAMAX JR Robotic Pool Cleaner Description

Price

1

A10203

Handle Assembly (Blue & White, Bracket Included) -

AquaMax BiTurbo, Ultramax Junior

Handle Bracket (Blue) - Al Aquabot except T2

and T4, All AquaMax, All UltraMax cleaners listed

Clevis Pin (Round Head, Hole in End) -

Use to link the Handle Assembly arm to the Handle Bracket

6

11004

Washer (St. Steel) - Use around the Clevis Pin

underneath the Cotter Ring on Handle Assembly Bracket

Cotter Ring (Aluminum, 3/16") -

Use at end of the Clevis Pin to hold the Handle Bracket

Screw (10-32, 7/8", Phil Pan Head) -

Use to fasten the Handle Bracket to the Body Assembly

Screw (#8, 11/16", Phil Pan Head) -

Use to fasten the Handle on UltraMax to Shell

--

2500

Screw (#8, 1-1/4" Pan Head) -

Use for Drive Motor Spacer Bracket if necessary

Hook (St. Steel, Snap-Hook, Eyelet for Pin) -

Used to fasten Rope Assembly to Handle on large cleaners

No Longer Available

12

2111

P-Clip (5/8", Coated Steel) -

Use to fasten the insulated part of a 4, 7, 9-wire cable to the Handle Assembly

P-Clip (11/16", St. Steel) -

Use to fasten the foam-insulated part of a 9-wire cable to the Handle Assembly

P-Clip (11/16", Plastic) -

Use to fasten the foam-insulated part of a 9-wire cable to the Handle Assembly

13

2700

Screws (#8, 11/16", Phil Pan - Flat Head) -

Use to fasten P-Clips, Side Plates, and Drive Motor

14

2260

Screws (#6, 7/16", Phil Pan - Flat Head) -

Use to fasten P-Clips, and Side Plates on Jet and Rover Cleaners

Plug (9-Pin, Female, 9-Wire) - UltraMax / Jr.

16

S7935

EZ-Swivel (For 4, 5, 7, or 9-Wire Cable) -

Can be used on any Cable Assembly with 4 or more wires

Cable Assembly (9-Wire, 120 Foot, Floating) -

Ultramax Jr., UltraMax

Cable Assembly (9-Wire, 150 Foot, Floating) -

Ultramax Jr., Ultramax     ** Optional extra length

Float Ball (Large) - for cable Assembly

** Position it the same distance from unit as maximum depth of pool

---

A8325

Rope Assembly (Blue & White, Nylon) -

Aquamax BiTurbo, Ultramax Jr., Power Handi-Vac 200

Connector (Sky Blue) - Use on Rope Assembly to form

a 'Y' shape to attach to sides of the Handle Assembly

Connector (Stainless Steel) -

For making small loops in the Nylon Rope Assembly

Outlet Top (Top, Bottom, & Cap) - UltraMax Jr. , Ultramax

A22201UJR

Body Assembly (White, w/Lock Tabs, Outlet Rings, Inserts) -

Ultramax Jr.

---

8351

Flat Plug (White, Plastic) -

Use to plug large holes on the Body Assembly

27

2251

Screw (8-18 x 3/4, Phil Small Head) -

Use for Pump to Body in some cleaners, and Jet Valve Assembly

No Longer Available

---

2400

Nail Plug (White, Plastic) -

Use to plug small holes on the Body Assembly

30

SP3402

Lock-Nuts (Hex, Nylon insert) - For various uses: Side Plate Bolts,

Anti-Roll Brackets, Pole Handle Assembly

No Longer Available

Lock-Tabs (Blue, Plastic) -

For all Body Assemblies, used to hold Bottom Lids to base of cleaners

38

2303

Screws (18-8, 8/32" x 1/2", Phil Bev Head) -

Use to fasten the Lock-Tabs to the Body Assembly

Lock-Nut (Nylon Insert, Hex) -

Use to fasten the Screws of the Lock-Tabs

Side Plate (Blue, 4 holes for Bolts, 2 holes to Motor) -

Aquabot Plus RC / Ultra, AquaMax / BiTurbo, Ultramax / Jr.

Screw (Bolts, Long, for Side Plate) -

Aquabot Plus RC, Aquabot Ultra, All AquaMax & UltraMax Units

Bushing (White, Plastic) - Pack of 4

All Aquabot cleaners, All listed AquaMax, and Ultramax cleaners

Small Roller (White, Plastic) -

Supports the Drive Track, install on lower legs of Side Plate

Stepped Sleeve Roller (White) -

Thicker end supports Drive Belts, Install on upper Side Plate legs

Drive Belts (Tan)

Pulley Assembly (Medium, ~ 2.75 in.) -

Use for cleaners with Black Drive Motors

Pulley Assembly (Long, Old, ~3.5 in.)  -

*** See Drive Motor Spacer Bracket # 8299

Washer - Use on all Pulley Assemblies, Use on moveable

Axle of Jet / Rover cleaners, Rounded edges facing forward

Tension Device (Old, Replaced by Stepped Sleeve Rollers) -

Formerly used to add Tension to Drive Belts

Pump Motor - Aquabot Plus RC, AB Ultra, AquaMax Jr. Plus,

AquaMax, AMAX BiTurbo, Ultramax Jr., UMAX

Propeller - All Cleaners

Washer (St. Steel) - Use with # 2500 screw

against Body Assembly to fasten Drive Motor Spacer Bracket

Junction Box Assembly (Connections: 9-Pin, 2 Pump Motor,

2 Drive Motor) - Ultramax Jr., Ultramax Jr BB

Junction Box Assembly (Connections: 9-Pin, 2 Pump Motor,

2 IR, 2 Drive) - Ultramax Jr. IR, UMAX Jr. BB IR)

Drive Motor (Master, Black) - Ultramax Jr., Ultramax

Drive Motor (Master, Black, BB Air Sensor) -

UltraMax Jr. Beach Boy, Ultramax Beach Boy

Drive Motor (Slave, Green) -

Use for all units which use two Drive Motors

---

SP3107

Motor Float ("8" Shape) -

** Only when specified by Aqua Products

*** Spacer Bracket (w/ hardware) -

Use when older Black Drive Motor Legs are too short for Pulley

Spiral Pin (3/4", Solid Stainless Steel) -

Used in the end of the Drive Motor shaft, use Lock-Tie

86

SP5474

Shrinkable Butt Connectors (Light Blue) -

Crimp closed and heat shrink to seal

Shrink Tube (5/16", Blue) -

For sealing 2-wire connections, use under Heat Shrink SP1619

Shrink Tube (1/2", Black) -

For sealing 2-wire connections, use over Heat Shrink SP1617

No Longer Available

Shrink Tube (3/4", Blue) -

For sealing the Cable insulation below the P-Clip at the Handle Assembly

No Longer Available

Shrink Tube (3/4", Black) -

For sealing all medium sized connections at the Junction Box

No Longer Available

Shrink Tube (1-1/2", 2.5", Black) -

Service kit for sealing large Cable connections

Shrink Tube (1-1/2", Black) -

For sealing wide connections at the Junction Box and Cable Assembly

A38201MG

Wheel Tube Assembly (New) - Model 'G'

Aquabot Ultra, Ultramax Jr.

Retaining Ring (E-Clip, New Style) - Aquabot Turbo,

AB Plus RC, Aquabot T4, AB Ultra, All AMAX / UMAX

Washer (Nylon, Flat) -

Use for all cleaners on the end of Wheel or Wheel Tube Assembly

1109

Screw (Small) - Aquabot Plus RC / Ultra, Ultramax Jr.

Use to fasten Wheel Tube Brace to Body

97

SP3002BM4

Rubber Brushes (Blue Molded Rubber, Cut in Half, Long) -

Aquabot Ultra, UltraMax Jr.

97

SP3008A

PVA Climbing Brushes (Light Blue PVA Foam, Cut in Half, Long) -

Aquabot Ultra, Ultramax Jr.

PVA Climbing Rings (Light Blue PVA, 1" thick) -

Fit over Rubber Brushes to add more traction **

Drive Track (Black)

Drive Track (Blue)

Drive Track with Traction Tabs (Blue) -

For all Model 'G' units - Single

Model G Spacer Bracket 

** necessary with 'Model G' Drive Tracks

101

8101

Filter Bag (Fine)

101

8201

Filter Bag (Mesh)

102

SP8001

Filter Bag Clip (Black, Plastic)

103

5301

Filter Screen (White, Cage)

Screw (#6, 11/16", Phil Pan-Flat Head, Pointed) -

For fastening the 5300/ 5301 Filter Screen to the Body

105

A9201XC

Bottom Lid Assembly (White, Square Wire Frame)

107

9301

Intake Valve Flap (Black PVC Rubber)

Power Supply (9-Pin, Male Socket, Radio RC) -

All Ultramax cleaners

Socket Assembly (9-Pin, Male, 9-Wire) -

Ultramax Jr., Ultramax

Dust Cap (Rubber, Looped, Removable) -

Ultramax Jr., Ultramax

Dust Cap (Plastic, Threaded, Chained) -

Ultramax Jr., Ultramax

Fuse Holder (Standard, Push & Turn style) -

Most residential and commercial cleaners

Fuse Holder (Alternate, Phillips Head Style) -

Only when specified by Aqua Products Service

Fuse (5.0 Amp, 250 Volt, Slow-Blow) -

Aquabot Plus RC, Aquabot Ultra, All AMAX, All UMAX, All PHV

On / Off Lighted Switch (Wide, Standard, Red, 3-Wire) -

Use for Power Supply

Antenna (4", with Hardware) -

Aquabot T4 / Plus RC / Ultra, UMAX Jr., UltraMax

116

220114C

Transmitter (Radio RC, Grey & Yellow/ Blue/ Red LED Light) - New

Units Only - Transmits to A220203FCC Receiver - Older Units will need Kit

No Longer Available

117

SP7041

Handle (Rubber, with Holders and Hardware) -

Ultramax Jr., Ultramax

No Longer Available

118

7102

Cord for Power Supply (3-Wire, Green, Black, and White) -

Use on all Power Supplies

119

7272

Outdoor Timer (8hr, Programmable, GFCI) -

Use to regulate cleaner's run time when no Auto shut-off

---

2007C

Infra Red Sensor - Ultramax / Jr.

---

2009

IR Brace Assembly (all hardware included) -

Use to hold the IR Sensor in position on the cleaner

---

2008

Screws (Use to hold IR Brace inside of Outer Shell) -

Screw from outside of shell into IR Brace Assembly

No Longer Available

---

1609

Tie (Blue, #4 Plastic, Reusable) -

Use for coiling the Cable Assembly among other things

BACK TO POOL CLEANER PARTS MAIN PAGE