AquaMax Jr. HT Robotic Pool Cleaner Parts Description

Handle Assembly (Blue & White, Bracket included) -

Aquabot/ Turbo/ Plus RC, AquaMax Jr.

Handle Bracket (Blue) - All Aquabot except T2 & T4, All AquaMax

Clevis Pin (Round Head, Hole in End) -

Use to link the Handle Assembly arm to the Handle Bracket

Washer (St. Steel) - Use around the

Clevis Pin underneath the Cotter Ring on Handle Assembly Bracket

Cotter Ring (Aluminum, 3/16") -

Use at end of the Clevis Pin to hold the Handle Bracket

Screw (10-32, 7/8", Phil Pan Head) -

Use to fasten the Handle Bracket to the Body Assembly

Screw (#8, 1-1/4" Pan Head) - Use on Back Plate Block,

and for White Drive Motors through Handle Assembly

P-Clip (1/4", Plastic) -

Use to fasten the non-foam-insulated part of a 2-wire cable to the Body

P-Clip (3/8", Plastic) -

Use to fasten the foam-insulated part of a 2-wire cable to the Body

P-Clip (7/16", Plastic) -

Use to fasten the foam-insulated part of a 2-wire cable to the Handle Assembly

P-Clip (9/16", Plastic) -

Use to fasten the Heat Shrink part of a 2-wire cable to the Handle Assembly

P-Clip (5/8", Coated Steel) -

Use to fasten the insulated part of a 4, 7, 9-wire cable to the Handle Assembly

Screws (#8, 11/16", Phil Pan-Flat Head) -

Use to fasten P-Clips, Side Plates, and Drive Motors

Screws (#6, 7/16", Phil Pan-Flat Head) -

Use to fasten P-Clips, Side Plates, and Outlet Top

Plug (3-Pin, Female, 2-Wire) -

Aquabot / Turbo / T2, AquaMax, AquaMax Jr.

Plug (4-Pin, Female, 4-Wire) -

Aquabot Turbo Solo / Turbo RC, AquaMax Jr. RC, AquaMax BiTurbo

EZ-Swivel (for 2-Wire Cable) -

Can be used on any 2-wire Cable Assembly

EZ-Swivel (for 4, 5, 7, or 9-wire Cable) -

Can be used on any Cable Assembly with 4 or more wires

Cable Assembly (for Tank Demo, 2-Wire, 10 Foot, Floating) -

Aquabot / Turbo, AquaMax Junior HT / Plus

No Longer Available

Cable Assembly (2-Wire, 75 Foot, Floating) -

Aquabot Plus, AquaMax Jr. HT

Cable Assembly (2-Wire, 100 Foot, Floating) -

AquaMax Jr. Plus

Cable Assembly (7-Wire, 120 Foot, Floating) -

AquaMax Jr. Plus RC, AquaMax BiTurbo RC

Outlet Top (Top and Bottom) -

Aquabot / Turbo / Plus / RC / Ultra, AquaMax / Jr. / BiTurbo

Body Assembly (White, with Lock Tabs, Pin, Outlet Ring, Inserts) -

Aquabot / Turbo, AquaMax Jr.

Body Assembly (White, with Lock Tabs, Pin, Outlet Ring, Inserts) - Aquabot Turbo Solo/ RC, AquaMax Jr. Solo/ RC

No Longer Available

Flat Plug (White, Plastic) -

Use to plug large holes on the Body Assembly

Screw (8-18 x 3/4, Phil Small Head) -

Use for Pump to Body in some cleaners, and Jet Valve Assembly

Anti-Roll Brackets (Plastic, White) -

Aquabot / Turbo / Plus RC / Ultra, AquaMax / Jr. / BiTurbo

Nail Plug (White, Plastic) -

Use to plug small holes on the Body Assembly

Lock-Nuts (Hex, Nylon insert) -

For various uses: Side Plate Bolts, Anti-Roll Brackets, Pole Handle Assembly

No Longer Available

Screw (M-5, Phil Bev Head) -

Use to fasten the Anti-Roll Brackets to the Body Assembly

Lock-Tabs (Blue, Plastic) -

For all Body Assemblies, used to hold Bottom Lids to base of cleaners

Screws (18-8, 8/32" x 1/2:, Phil Bev Head) -

Use to fasten the Lock-Tabs to the Body Assembly

Lock-Nut (Nylon Insert, Hex) -

Use to fasten the Screws of the Lock-Tabs

Side Plate (Blue, 4 holes for bolts) -

AquaMax Jr. HT, AquaMax Jr. Plus

Screw (Bolts, Long, for Side Plate) -

Aquabot Plus RC, Aquabot Ultra, All AquaMax

Bushing (White, Plastic) - Pack of 4

All Aquabot cleaners, All listed AquaMax, and Ultramax cleaners

Bushing (White, Plastic) - Use for Pin on Body Assembly -

Aquabot / Turbo, All AquaMax

Small Roller (White, Plastic) -

Supports the Drive Track, install on lower legs of Side Plate

Large Roller (White, Plastic) -

Supports the Drive Track, installs on Body Assembly Pin Support

Stepped Sleeve Roller (White) -

Thicker end supports Drive Belts, Install on upper Side Plate legs

Drive Belts (Tan)

Pulley Assembly (Short, ~ 2.5 in.) -

Use for cleaners with White Drive Motors

Pulley Assembly (Medium, ~ 2.75 in.) -

Use for AquaMax Jr. Plus Solo Drive Motor

Washer - Use on all Pulley Assemblies, Use on moveable

Axle of Jet / Rover cleaners, Rounded edges facing forward

Tension Device (Old, Replaced by Stepped Sleeve Rollers) -

Formerly used to add Tension to Drive Belts

Pump Motor - Aquabot Turbo, Aquabot Tempo, AquaMax Jr. Ht

Pump Motor - Aquabot Plus RC, AquaMax Jr. Plus, AquaMax

Propeller - All Cleaners

DC Pump Filter (White, Plastic) -

Aquabot Turbo Solo/ Turbo RC, All AquaMax RC / Solo cleaners

Tubing (Clear PVC, 5/16" ID x 7/16" OD) -

Use to divert water from the DC Pump Filter to the DC Pump

Spacer Block (Grey, Stepped shape) -

Use to position the Piston apart from the Model g Drive Tracks

DC Pump Motor (Single, no Gate, 2-Wire) -

Aquabot Turbo Solo, All AquaMax Solo/ IR cleaners

DC Pump Motor (Dual, with Gate, 2-Wire) -

Aquabot Turbo RC, Aquabot T4, All AquaMax RC cleaners

Tubing (Clear PVC, 3/16" ID x 5/16" OD) -

Use to divert water from the DC Pump to the Piston Assembly

No Longer Available

Clamp (Grey, Plastic, Narrow) -

Aquabot Turbo Solo / RC / T4, All AquaMax RC / Solo cleaners

No Longer Available

Clamp Bracket (Grey, Plastic, Wide) -

Aquabot Turbo Solo / RC, All AquaMax RC / Solo cleaners

Back Plate Block (Grey, 4 holes) -

Use to Support the DC Pump Motor inside of the Body Assembly

No Longer Available

Spacer (Plastic, cylinder) -

Use to make space between the Back Plate Block and the Body Assembly

No Longer Available

Screw (10-32, 1-3/4" Phil Pan Head) -

Use to fasten Clamp & Piston onto Side Plate of a Model G cleaner

Screw (10-32, 1/2" Phil Pan Head) -

Use with Clamp to fasten Piston to Side Plate and DC Pump to Block

No Longer Available

Washer (St. Steel) - Use with # 2500 screw

against Body Assembly to fasten Back Plate Block to Body

Piston Assembly (White, Plastic) -

One Piston is used for Solo cleaners, Two are used for RC cleaners

Rubber Tip (White, Rubber) -

Use at the bottom of the plunger of the Piston Assembly

Drive Motor (White, Terminal Basin, for Tank Demo unit) -

Aquabot / Aquabot Turbo Tank Demo

Drive Motor (White, Terminal Basin) - AquaMax Jr. HT

Drive Motor (White, Terminal Basin) - AquaMax Jr. Plus

Drive Motor (Black, bare wire leads) - AquaMax Jr. Plus IR

No Longer Available

Drive Motor (Black, bare wire leads) - AquaMax Jr. Plus Solo

Drive Motor (Black, bare wire leads) - AquaMax Jr. Plus RC

Loop Connector (Metal, Crimp on wire) -

Use to attach wires to Brass Terminals on White Drive Motor

Brass Nuts (Hex, Small) -

Use for attaching the Loop Connectors of wires to Brass Terminals

Spiral Pin (3/4", Solid Stainless Steel) -

Used in the end of the Drive Motor shaft, use Lock-Tie

Putty (Grey, Waterproof) -

For waterproofing the Terminal Basin in all White Drive Motors

Terminal Cover (Plastic, Rectangle) -

For covering the Basin in all White Drive Motors

Screw (8-18 x 1/2, Phil Pan Head) -

Use to fasten the Terminal Cover and the Extension Brackets

Shrinkable Butt Connectors (Light Blue) -

Crimp closed and heat to shrink to seal

Shrink Tube (5/16", Blue) -

For sealing 2-wire connections, use under Heat Shrink SP1619

Shrink Tube (1/2", Black) -

For sealing 2-wire connections, use over Heat Shrink SP1617

No Longer Available

Shrink Tube (3/4", Blue) -

For sealing the Cable insulation below the P-Clip at the Handle Assembly

No Longer Available

Wheel Tube Assembly (Old) -

AquaMax Jr. HT, AquaMax Jr. Plus

Wheel Tube Assembly (New) - Model 'G'

AquaMax Jr. HT, AquaMax Jr. Plus

Retaining Ring (E-Clip, New Style) -

Aquabot Turbo, AB Plus RC, Aquabot T4, All AMAX

Washer (Nylon, Flat) -

Use for all cleaners on the end of Wheel or Wheel Tube Assembly

Sponge Brushes (Black Sponge Foam, Short) -

Aquabot, Turbo, AquaMax Jr. HT, AquaMax Jr. Plus

Rubber Brushes (Blue Molded Rubber, Short) -

Aquabot / Turbo, AquaMax Jr. HT / JR. Plus, Ultramax ***

Rubber Brushes (Black Molded Rubber, Short) -

Aquabot / Turbo / T4, AquaMax Jr. units, Ultramax ***

PVA Climbing Brushes (Light Blue PVA Foam, Short) -

Aquabot / Turbo, AquaMax Jr. HT units, Ultramax ***

PVA Climbing Rings (Light Blue PVA, 1" Thick) -

Fit over Rubber Brushes to add more traction **

Drive Track (Black)

Drive Track (Blue)

Drive Track with Traction Tabs (Blue) - For all Model 'G' units - single

Model Spacer Brackets - ** necessary with Model 'G' Drive Tracks

Filter Bag (Fine) - Aquabot / Turbo / Plus RC,

AquaMax Jr., PHV 100/300, small Jet / Rover, UMAX **

Filter Bag (Mesh) - Aquabot / Turbo / Plus RC,

AquaMax Jr., PHV 100/300, small Jet / Rover, UMAX **

Filter Screen (White, Cage) - Aquabot / Turbo / Plus RC,

AquaMax Jr., PHV 100/300, small Jet / Rover, UMAX **

Screw (#6, 11/16", Phil Pan-Flat Head, Pointed) -

For fastening the 5300 / 5301 Filter Screen to the Body

Bottom Lid Assembly (White, W-Shaped Wire Frame) -

Aquabot, small Jet / Rover, AquaMax Jr., Ultramax ***

Intake Valve Flap (Blue Plastic) -

Fits into Intake of all small # 9200 Bottom Lids

H-Float (Foam, Plastic, with Screws) -

Fasten to Bottom Lid if cleaner's wall-climbing is not high enough

Weights (Black) - Put in Bottom Lid if cleaner's wall

climbing is too high, or to help JetMax / Jr. sink to floor

Side Pocket Floats (White, Foam Blocks) -

Put in Bottom Lid if wall-climbing is not high enough

Power Supply (3-Prong, Male Socket) -

AquaMax Jr. HT, AquaMax Jr. Plus, AquaMax, PHV 100

Power Supply (4-Prong, Male Socket) -

AquaMax Jr. Plus RC, AquaMax RC

Socket Assembly (3-Pin, Male, 2-Wire) -

Aquabot / Turbo / T2, All Jet and Rover cleaners, AquaMax / Jr.

Socket Assembly (4-Pin, Male, 4-Wire) -

Aquabot Turbo Solo / Turbo RC, AquaMax BiTurbo

Fuse Holder (Standard, Push & Turn Style) -

Most Residential and Commercial cleaners

Fuse Holder (Alternate, Phillips Head Style) -

Only when specified by Aqua Products Service

Fuse (5.0 Amp, 250 Volt, Slow-Blow) -

Aquabot Plus RC, Aquabot Ultra, All AMAX, All UMAX, All PHV

On / Off Lighted Switch (Wide, Standard, Red, 3-Wire) -

Use for Power Supply without Dial Timer

Antenna (4", with Hardware) -

AquaMax Jr. Plus RC, AquaMax RC, AquaMax BiTurbo RC

116

220117C

Transmitter (Radio RC, Grey & Yellow/ Blue/ Red LED Light) - New

Units Only - Transmits to A220200FCC Receiver - Older Units will need Kit

No Longer Available

117

7041A

Handle (Plastic, with Hardware) -

Use on All Power Supplies except Ultramax

118

7102

Cord for Power Supply (3-Wire, Green, Black, and White) -

Use on all Power Supplies

119

7272

Outdoor Timer (8hr, Programmable, GFCI) -

Use to regulate cleaner's run time when no Auto shut-off

---

2209

Infra Red Sensor

---

2009

IR Brace Assembly (all hardware included) -

Use to hold the IR Sensor in position on the cleaner

---

2008

Screws (Use to hold IR Brace inside of Outer Shell) -

Screw from outside of shell into IR Brace Assembly

No Longer Available

---

1609

Tie (Blue, #4 Plastic, Reusable) -

Use for coiling the Cable Assembly among other things

---

A800135

Main Drain Bumper -

Can be used on most Pools' Main Drain, where a cleaner may get stuck

 All Aquabot Junior PLUS Cleaner Parts are Original AQUABOT Replacement Parts, and spares for the Aquabot

 To purchase more than 1 aquabot Jr. PLUS part, hit the

button in the Shopping Cart